Clone A Willy Instructions

Clone a Willy Instructions

Clone A Willy Vibrator Moulding Kit Black Main

Wondering how to make a Clone A Willy? When you purchase any mould a willy kit, it should arrive with a full set of instructions. However, we appreciate that these instructions can get lost. So, in this blog we will provide the full Clone a Willy instructions needed to immortalise your member in all its glory.

Table of Contents


What Is a Clone a Willy Kit?

Clone a Willy kits provide the unique opportunity to produce an exact replica of a person’s penis. They use a silicone mixture to mould the shaped of the penis and turn it into a special one off dildo. The two biggest brands of penis moulding kits are Clone A Willy and Cloneboy.

Clone a Pussy kits are available also but in this blog we will focus on how to make a Clone a Willy.


Clone a Willy Kit Contents

Clone A Willy Deep Tone Vibrating Kit Contents

Each kit will contain the following items needed to make the clone:

  • Moulding tube
  • Specially timed moulding powder
  • Two-part platinum-cure silicone mix
  • Single-speed vibrating unit
  • Full instructions
  • Thermometer
  • Stirring stick

What Else Do I Need to Make a Clone a Willy?

But you are going to need the following items as well and these as there are not included.

  • A penis (or was that too obvious?!)
  • Measuring jug
  • Mixing bowl
  • Clean disposable container such as a paper cup.
  • Spatula
  • Timer
  • Pair of scissors
  • Pen
  • A small piece of cardboard

Before you can start, you’ll need to gather all the necessary items. Creating a Clone-A-Willy isn’t overly complex, but the mixture sets rapidly, so you must work swiftly for the best possible result.


Step By Step Clone a Willy Instructions

Now that you’ve gathered all the essentials, it’s time to enjoy the exciting part.

Read the Clone a Willy instructionsWhile it might seem obvious, many individuals overlook reading the instructions and consequently end up dissatisfied with the results. Investing time to thoroughly go through the Clone A Willy instructions makes a big difference and could potentially prevent wasting money.
Prep the penisYou’ve spent time getting everything together, now it’s time to focus on the main star. Ready the penis. Trim the pubic hair and ensure cleanliness. Neglecting to trim the pubic hair could lead to discomfort. Picture a waxing session…you get the idea.
Stand to attentionAchieve an erection, aiming for maximum firmness. Get aroused and indulge in some foreplay. The penis needs to be as erect and firm as possible. Let’s face it, nobody wants themselves immortalised looking less than their best. Once erect, hold the moulding tube next to your erection and mark its length. Then, cut the tube along the marked line.
Get messyPour 425ml of hot water into the mixing bowl. Using the thermometer provided, confirm the water temperature is precisely 32°C (90 °F). Once the water reaches the correct temperature, add the moulding powder. Then, use the provided spatula to mix for 45 seconds. Afterward, pour the mixture into the tube. Now, insert your erect penis into the tube and press firmly against the body. Maintain this position for 4 minutes. After the 4 minutes have elapsed, gently remove your penis.
ChillThe mould now needs time to set. It is recommended that this is done overnight but if you can’t wait that long, 4 hours will do.
Get mixingEmpty both jars of silicone mixture into a disposable container and blend using the supplied wooden stirrer. Inspect the penis mould for any water accumulation and eliminate any excess before pouring in the silicone mix. Be sure to pour the mixture slowly to prevent air bubbles.
Time for the good vibesCut a square piece of cardboard big enough to sit over the top of the tube. Now cut an X in the middle. Insert the vibrating unit through the X and into the silicone mix. The cardboard should prevent the vibrator from sliding down into the mix before it has had time to set. Leave upright for 24 hours.
Play timeRemove the cardboard before pulling the dildo out of the mould. Go slowly and gently. If there is any excess silicone around the base, this can be trimmed with scissors for a clean finish. Finally insert a AA battery and your Clone a Willy is ready to play.

Top Tips for How to Make a Clone a Willy

Clone A Willy Light Tone Vibrating Kit Contents
  • Using a cock ring can help to keep an erection firm and full during the process.
  • Sharing a drink during this activity may seem like a good idea but being tipsy and following instructions is never a good recipe. Things could go wrong.
  • Whilst it may be tempting to remove your cast before it has had time to set, don’t. If it is removed too early it could all fall apart making the kit good for nothing other than the kitchen bin. Be patient. It will be worth it.
  • These kits are only suitable for use with a willy. They are not designed to be used with other body parts.
  • Most importantly, have fun!

Bestselling Clone a Willy Kits

Clone A Willy Glow In The Dark Vibrator Moulding Kit Green Main

Clone-A-Willy Glow In The Dark Vibrator Moulding Kit Green

We love this version of the Clone a Willy kit. All the usual fun of creating a replica version of your lover’s penis but this one glows in the dark!


Clone-A-Willy Vibrator Moulding Kit Neon Purple

Clone-A-Willy Vibrator Moulding Kit Neon Purple

In a vibrant purple, this willy moulding kit is a for those who enjoy something a little different. Fun and funky, this neon coloured kit certainly makes a statement.


Clone A Willy Vibrator Moulding Kit Light Skin Tone Main

Clone-A-Willy Vibrator Moulding Kit Light Skin Tone

Looking for a more realistic dildo experience then why not plump for one of the natural skin tone models. In a light tone, brown and black these kits can ensure truly lifelike stimulation.

Best Sex Toys for Swingers
Can I Take My Sex Toys on Holiday?

Leave a Reply

Your Basket
Wishlist
Recently Viewed
Categories